RESEARCH ON THE APPLICATION OF QFORM SOFTWARE FOR ROLLING SMALL-SIZED CONICAL BILLETS

Authors

  • Berdiyev Darob Muratovich Scientific Secretary of the Scientific and Technical Center for Radiation and Nuclear Safety
  • Saydumarov Botir Muradovich Department of Metal Technologies Faculty of Mechanical Engineering Tashkent State Technical University
  • Tashmatov Ravshan Kobilovich Head of the Department of Technological Machines and Equipment, Almalyk State Technical Institute
  • Xasanov Kamoliddin Akmal o‘g‘li Department of Metal Technologies Faculty of Mechanical Engineering, Tashkent State Technical University
  • Mo‘minov Afzalsho Oljabay o‘g‘li Master’s Student (Group 60M-25) Tashkent State Technical University

Abstract

The development of a rolling process technology regime using simulation with the QForm software package for forming the base of a cutting tooth used in mineral extraction from 35XGSA steel billets produced by JSC “Uzmetkombinat” is considered one of the urgent problems. The rolling process is a metal forming process in which the material is deformed by passing it between rolling rolls, and it is widely used in industry. Conical workpieces (billets) are often required for products such as bushings, pins, and conical adapters. In traditional experimental production, the development of such parts requires significant time and resources. Therefore, preliminary verification and optimization of the technology through computer simulation is an effective solution.

References

Saydumarov B.M. Prokatlash mashinalari va jihozlari. Darslik. Toshkent: TDTU, Bookmany print, 2026. 267 b.

Saydumarov B.M. Prokatlash uskunalarini loyihalash. Darslik. Toshkent:TDTU, Bookmany print, 2023. 236 b.

Humphreys F.J., Hatherly M. Recrystallization and Related Annealing Phenomena. Elsevier, 2004.

Allenov, M. G., & Belokurov, O. A. (2020). Evaluation of the Friction Factor Influence on the Results of Cross‑Wedge Rolling Simulation in QForm Software. Solid State Phenomena, vol. 299, pp. 494–500. https://doi.org/10.4028/www.scientific.net/SSP.299.494

Guseynov, E. R., Aleshchenko, A. S., Fortunatov, A. N., & Korol’, A. V. (2025). Experimental study of tool wear in the production of seamless hot‑rolled pipes using QFORM software package. Chernye Metally, 10, 52–58.

Gerasimov, D., & Gartvig, A. (2016). Parallel computing of metal forming simulation in QForm software. Computer Methods in Materials Science, 16(3), 139–142. https://doi.org/10.7494/cmms.2016.3.0582

Saydumarov B.M. Prokatlash jo‘valarining konstruksiyasi, ishlash sharoiti, ekspluatatsion xossalarini tahlili va ularning chidamliligini oshirish usullari. Kompozitsion Materiallar. №1, 2026 (215-216).

Downloads

Published

2026-04-01

How to Cite

Berdiyev Darob Muratovich, Saydumarov Botir Muradovich, Tashmatov Ravshan Kobilovich, Xasanov Kamoliddin Akmal o‘g‘li, & Mo‘minov Afzalsho Oljabay o‘g‘li. (2026). RESEARCH ON THE APPLICATION OF QFORM SOFTWARE FOR ROLLING SMALL-SIZED CONICAL BILLETS. INTERNATIONAL JOURNAL OF SOCIAL SCIENCE & INTERDISCIPLINARY RESEARCH ISSN: 2277-3630 Impact Factor: 8.036, 13(04), 1–5. Retrieved from https://www.gejournal.net/index.php/IJSSIR/article/view/2891

Issue

Vol. 13 No. 04 (2026): INTERNATIONAL JOURNAL OF SOCIAL SCIENCE & INTERDISCIPLINARY RESEARCH

Section

Articles

License

Copyright (c) 2026 GEJournals

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Creative Commons Attribution- 3.0 Unported License.